Call us now:
Quick answer: Cr8 Cold Work Tool Steel Forging is available for made-to-order and project supply. Cr8 is an 8% chromium-class cold-work die-steel designation selected where a practical balance of wear resistance, hardenability and resistance to edge damage is required. Quote confirmation is based on the governing specification, required dimensions, delivery condition, inspection scope and authenticated mill availability.
Request Cr8 Cold Work Tool Steel Forging with the required standard, dimensions, tolerance, finish, inspection and mill test certificates from SAKY METAL.
Technical procurement data
Standards, supply and inspection
Cr8 Cold Work Tool Steel Forging Cr8 is an 8% chromium-class cold-work die-steel designation selected where a practical balance of wear resistance, hardenability and resistance to edge damage is required.
| Material / grade | Cr8 |
|---|---|
| Product form | Forging |
| Standards and order reference | Chinese/commercial cold-work tool-steel designation; the approved grade specification and chemistry limits must be stated on the purchase order. |
| Dimensions and tolerances | Finished or forging dimensions to drawing; forging ratio, machining allowance and tolerances agreed during technical review |
| Surface and supply condition | As-forged, shot-blasted, rough-machined, fully machined or customer-specified |
| Inspection options | Chemistry, hardness, dimensions, visual inspection and ultrasonic testing where ordered. |
| MTC and traceability | EN 10204 3.1 MTC or agreed certificate type with heat/lot traceability. |
| Typical applications | blanking and forming dies, punches and die inserts, shear and slitter tooling, wear-resistant tooling components |
| RFQ checklist | Send grade/specification, dimensions, quantity, condition, inspection, documentation and delivery destination. |
Final compliance is defined by the purchase order, approved drawing and issued mill documentation. Availability is confirmed for each grade, size and production route.
SAKY METAL supplies Cr8 as forging for cold-work tooling and engineered wear applications. Available production routes include open-die forged blocks, discs, rings, shafts or drawing-specific near-net shapes, subject to grade and mill capability. Every order is reviewed against the drawing, finished tool size, machining allowance, heat-treatment plan and documentation requirements.
| Grade | Cr8 |
|---|---|
| Material family | Cold-work tool steel |
| Product form | Forging |
| Specification basis | Chinese/commercial cold-work tool-steel designation; the approved grade specification and chemistry limits must be stated on the purchase order. |
| Supply route | open-die forged blocks, discs, rings, shafts or drawing-specific near-net shapes, subject to grade and mill capability |
| Dimensions | Finished or forging dimensions to drawing; forging ratio, machining allowance and tolerances agreed during technical review |
| Surface options | As-forged, shot-blasted, rough-machined, fully machined or customer-specified |
| Processing services | open-die forging, heat treatment, saw cutting, rough machining, boring and ultrasonic inspection where specified |
| Documentation | EN 10204 3.1 MTC or agreed certificate type, heat/lot traceability and inspection reports as ordered |
Grade Characteristics
Cr8 is an 8% chromium-class cold-work die-steel designation selected where a practical balance of wear resistance, hardenability and resistance to edge damage is required.
- Balanced wear resistance and toughness for cold-work tooling
- Good hardenability for appropriately sized sections
- Suitable for machining, heat treatment and optional surface engineering under a qualified route
Ordering note: Cr8 can refer to supplier-specific variants. Confirm the full designation, chemistry, heat-treatment response and acceptance limits before manufacture.
Typical Applications
The correct grade and hardness must be selected from the actual failure mechanism—abrasive or adhesive wear, edge chipping, gross cracking, plastic deformation or dimensional change. Typical enquiries include:
- blanking and forming dies
- punches and die inserts
- shear and slitter tooling
- wear-resistant tooling components
- large die blocks, rings, heavy inserts, shafts and high-load tooling components
Delivery Condition and Processing
Material is normally quoted in an annealed machining condition unless the purchase order requires another approved condition. Available services can include open-die forging, heat treatment, saw cutting, rough machining, boring and ultrasonic inspection where specified. Requested decarburization allowance, machining stock, grain-flow direction and test locations should be shown on the drawing.
Heat treatment is not one universal cycle. Austenitizing, quenching, tempering, sub-zero treatment and surface coating must follow the actual certified grade, section size, furnace capability and final hardness requirement. Obtain approval before substituting a related grade.
Inspection, MTC and Traceability
The inspection plan may include positive material identification, chemical-composition review, annealed hardness, dimensions, straightness or flatness, visual surface inspection, decarburization checks, and ultrasonic testing where section size and service criticality justify it. Third-party inspection can be coordinated when stated before quotation.
Specify EN 10204 3.1 certification or the required certificate type, heat and lot traceability, marking, packing, country-of-origin requirements and any approved-mill list in the RFQ. Final compliance is defined by the purchase order, approved drawing and issued mill documentation.
How to Request a Quote
- State the exact grade and governing standard or approved producer datasheet.
- Send finished or forging dimensions to drawing; forging ratio, machining allowance and tolerances agreed during technical review.
- Define quantity, delivery condition, surface, machining allowance and final application.
- List hardness, ultrasonic, cleanliness, certification, marking and third-party inspection requirements.
- Provide the delivery destination and required schedule.
Request a quote for Cr8 Forging
Frequently Asked Questions
Can you cut Cr8 forging to size?
Yes. Cutting and machining options depend on size, tolerance, quantity and delivery condition. Send a drawing or finished dimensions so machining allowance can be reviewed.
Is Cr8 supplied with an MTC?
Certification can be supplied as ordered. State EN 10204 3.1 or another required certificate type and any authenticated-producer requirement before quotation.
Can Cr8 be substituted with a related cold-work grade?
Only after engineering and customer approval. Similar application groups can have different chemistry limits, carbide structures, heat-treatment schedules, dimensional response and trademark status.
What information is needed for heat treatment?
Provide the certified grade, section size, target hardness, service failure mode, dimensional requirements and any coating or EDM operations. The heat treater should use the governing standard or current producer datasheet.